Every water loss a US restoration contractor touches gets two labels from the same standard. ANSI/IICRC S500, the Standard for Professional Water Damage Restoration, now in its 2021 edition, assigns each loss a category and a class. The two labels answer different questions, and a file that mixes them up reads wrong to an adjuster.
Two axes, two questions
Category describes the water: the contamination at the source and how it changes with time. Class describes the building: how much water the materials have absorbed and how hard that water will be to evaporate. Category is about what the water can do to people. Class is about what it will take to get the water back out.
The two are independent, which is why both are needed. A supply line that bursts above a plaster ceiling and a hardwood floor is clean water held in materials that release it slowly: Category 1, Class 4. A small sewer backup onto a tile bathroom floor is grossly contaminated water on surfaces that barely absorb it: Category 3, Class 1. Read either label alone and the plan is wrong.
The three categories
S500 defines three categories. The examples are the standard's own; the inspection settles the call on a real loss.
Category 1: sanitary source
Water from a sanitary source that poses no substantial risk from contact, inhalation or ingestion. A broken supply line and a tub overflow with no contaminants are the standard's examples. Restorable materials it has wet can usually be dried in place.
Category 2: significant contamination
Water with significant contamination that can cause discomfort or sickness if contacted or consumed. The examples include dishwasher or washing machine discharge, and a toilet overflow on the room side of the trap with urine but no feces.
Category 3: grossly contaminated
Water that is grossly contaminated and can contain pathogenic, toxigenic or otherwise harmful agents. Sewage and rising floodwater are the obvious examples; so is water from any source that has sat long enough to deteriorate. Porous materials that contacted it, such as carpet, cushion, wallboard and insulation, are removed. What remains is cleaned and disinfected, and only then dried.
How category drives the work
- Safety and PPE. Category 2 and 3 work calls for respiratory protection, eye protection, gloves and protective clothing suited to the contamination, per the standard and OSHA. Category 1 work uses ordinary extraction protection.
- Containment. Category 3 work is contained so demolition and cleaning do not carry contamination into unaffected rooms, with air filtration where the work puts material into the air.
- Removal versus drying. Category 1: dry in place when the material is restorable. Category 2: replace the cushion, clean and assess the carpet, judge wallboard case by case. Category 3: remove every porous material that touched the water, then clean and disinfect what is left.
- Cleaning before drying. On a Category 2 or 3 loss, cleaning comes first. Air movers pointed at contaminated material spread it through the structure.
- Pricing. Estimating platforms price many water mitigation line items by category, so the category on the estimate must match the report and the photos.
How class drives the drying plan
Class is judged by estimating what share of the affected area's combined floor, wall and ceiling surface is wet porous material, then asking whether any low-evaporation material has taken on water. The standard gives approximate ranges. They are guidance, not a measurement.
| Class | Wet porous share of floor, wall and ceiling area | What it looks like | Drying implication |
|---|---|---|---|
| Class 1 | Roughly under 5 percent | A leak contained on tile, a small patch of wet carpet, water that never reached the walls | Lowest evaporation load; the fewest dehumidifiers |
| Class 2 | Roughly 5 to 40 percent | Carpet and cushion wet across part of a room, wicking up the walls | Moderate load; standard equipment and timeline |
| Class 3 | More than roughly 40 percent | Water from above that has wet ceiling, walls, insulation and floor | Highest evaporation load; the most dehumidification |
| Class 4 | Judged by the materials, not the share | Water deeply held or bound in hardwood, plaster, concrete, masonry or multilayer assemblies | Special methods, longer drying, larger vapor pressure differentials |
Dehumidifier math by class
The IICRC's initial dehumidification factor chart (Imperial, revision 3.1.22) turns class into a first-day dehumidifier size. For refrigerant units, divide the cubic feet of the affected area by the factor for its class; the result is the pints per day the dehumidifiers in that area must remove between them. For desiccants the chart gives air changes per hour.
| Class | Conventional refrigerant | Low grain refrigerant (LGR) | Desiccant, air changes per hour |
|---|---|---|---|
| Class 1 | 100 | 100 | 1 |
| Class 2 | 40 | 50 | 2 |
| Class 3 | 30 | 40 | 3 |
| Class 4 | Not applicable | 40 | 3 |
A living room 20 by 15 feet with an 8 foot ceiling is 2,400 cubic feet. As a Class 2 loss dried with LGR units, 2,400 divided by 50 is 48 pints per day. As Class 3 it is 2,400 divided by 40, or 60 pints per day. As Class 1 it is 24. For a desiccant on the same Class 2 room, 2 air changes per hour of 2,400 cubic feet is 4,800 cubic feet per hour, or 80 cubic feet per minute.
Air mover counts follow class as well; the companion article on air movers and dehumidifiers under S500 covers that arithmetic.
Making the call on the first visit
- Find the source and stop it. Note what it is: supply line, drain line, roof, appliance, toilet, ground water.
- Establish the timeline. Ask when the water started and when it was found; if nobody knows, estimate from the evidence and say so.
- Walk the water path: which rooms, which materials, how far up the walls, under the cabinets, into the subfloor, down to the level below.
- Survey moisture. Sweep floors and walls with a non-invasive meter, confirm with a pin meter, mark the wet boundary, and read unaffected material of the same kind for the dry standard.
- Decide the category from the source, the time elapsed, visible contamination and odor.
- Decide the class from the share of wet porous surface and whether any low-evaporation material is wet.
- Record both per affected area with the reason, date and time, and photograph the source and the extent before anything is moved.
One category and one class per affected area, not per job. The kitchen with the burst supply line may be Class 3 while the hallway it ran into is Class 1, and a basement with a sewer backup is Category 3 while the upstairs bathroom with a cracked tank is Category 1.
On the AIFSOP iOS app, each affected area is set up with its own category and class, its dimensions come from the LiDAR scan or manual entry, and the equipment suggestions for the area follow from that volume and that class. The determination sits beside the area's readings and photos instead of in a note somewhere else; the field app page describes the rest.
Why the labels change during the job
Category worsens with time, temperature and contact. A supply line fails on a Friday evening in a house whose owners are away. The water is Category 1 when it starts. By Tuesday it has sat four days in a warm house, the carpet smells, and there is growth at the base of the wallboard. The source was sanitary; the water in the house is not. Depending on what the inspection finds it is now Category 2 or 3, and the plan changes from drying in place to removal, cleaning and then drying.
Contact does the same thing faster: clean water through a dirty crawl space or a wall cavity with old growth has picked up what it touched. Grade it by what it became.
Class moves too, usually for the better as the wet boundary shrinks. It can also go up: a subfloor assembly that read dry on day one and holds water underneath on day two makes that area Class 4, whatever the first entry said. Every change gets its own dated entry with the reason and the readings or photos behind it. The day-one determination stays as written; the change entry explains why day three looks different.
Common losses and their likely labels
Starting points for losses that come up every week. The on-site survey decides the final call.
| Scenario | Likely category | Likely class | Notes |
|---|---|---|---|
| Supply line burst under a kitchen sink, found the same day | 1 | 1 or 2 | Water held in the toe kick or subfloor moves the class up |
| Washing machine discharge across a laundry room into a carpeted hall | 2 | 2 | Cushion replaced; carpet cleaned and assessed |
| Toilet overflow on the room side of the trap, urine only | 2 | 1 or 2 | Clean before drying |
| Sewer backup into a finished basement | 3 | 2 or 3 | Containment, PPE, porous materials out, clean and disinfect, then dry |
| Second floor pipe break while the family was away for a week | 1 at the source; likely 2 or 3 at discovery | 3 | Time and temperature; look for odor and growth |
| Creek or river floodwater into a ground floor | 3 | 3 or 4 | Slab, masonry and framing hold water after the surfaces look dry |
| Refrigerator supply line seep under hardwood for weeks | 1 at the source; reassess at discovery | 4 | Bound water in hardwood; specialty drying |
What adjusters expect to see in the file
- A category and a class for each affected area, dated, with the source and timeline behind the category and the moisture survey behind the class.
- Photos of the source, the extent of the water and any sign of contamination, with odor noted in writing.
- A moisture map with the dry standard, the wet boundary and the first readings.
- An equipment list with counts and placement, and the arithmetic behind it: cubic feet, class, factor, pints per day.
- Daily readings and moisture logs that show the plan working, or being changed when it did not.
- For Category 2 and 3: what was removed, why it could not be dried, and the cleaning steps that came before drying.
- A dated entry for every change in category or class, with the reason.
Reviewers read for consistency as much as completeness. A Category 1 report attached to an estimate with Category 3 extraction lines draws a question every time. AIFSOP builds its drying report from the readings, photos and equipment records entered against each area, each with its timestamp, so the reviewer reads the same file the crew built.
Common mistakes
- One category and one class for the whole job. Losses are graded per affected area.
- Judging class by gallons. Class is about the share of wet porous surface and the materials, not the volume of water that came in.
- Measuring that share against the floor alone. The ranges refer to the combined floor, wall and ceiling surface area.
- Calling a loss Category 1 because the source was clean, without asking how long the water sat or what it touched.
- Treating Class 4 as Class 3 with more equipment. Bound water in hardwood, plaster or concrete needs specialty drying methods and time, not more air movers.
Category and class are the two sentences at the top of every water loss. Get them right on the first visit, record the reasons, revise them in the open when the loss changes, and the rest of the file, from the equipment list to the invoice, has something to stand on.